Cost Guides · 2026

Roof Replacement Cost per Square Foot (2026)

Roof replacement costs $5.21–$6.82 per square foot in 2026, or $521–$682 per roofing square. See prices by material, pitch and state.

$5.21–$6.82

Short answer

Roof replacement costs $5.21–$6.82 per square foot in 2026, or $521–$682 per roofing square. See prices by material, pitch and state.

Calculator

Roof cost calculator

Preset to the national labor baseline and a 2,000 sq ft home (2,240 sq ft of roof). Change any input for an itemized 2026 estimate. The link in your address bar saves your inputs.

01

Material

Model rate: $5.21–$6.82 per roof sq ft installed.

02

Roof area

Area unit

Roof surface, not floor area. One roofing square = 100 sq ft. 2,240 sq ft = 22.4 squares.

03

Roof pitch

Steeper roofs take more labor and safety setup.

04

Complexity

05

Stories

06

Old layers to tear off

Tear-off: $39–$53 per square per layer.

07

Location

State labor factor from BLS roofer wages. ZIP is optional and never stored.

+

Extras (optional)

Itemized planning estimate

Your roof bill

National baseline · 2,240 sq ft roof

Planning estimate
Materials & installation2,240 sq ft × $5.21–$6.82 × 1.00 adjustments$11,670–$15,280
Tear-off22.4 squares × $39–$53 × 1 layer$870–$1,190
Permits & disposalModel default, scaled to 1.6× at the high end$300–$480
Decking contingency10% of base, for damaged decking found mid-job$1,160–$1,530

Estimated installed total · Architectural Asphalt Shingles

$14.0k–$18.5k
Low$14,000
Typical (midpoint)$16,200
High$18,500

$630–$820 per roofing square, all in. Planning life 25–30 years.

Not included: gutters and structural repairs beyond decking.

Planning estimate only, not a contractor quote. Actual cost depends on roof condition, local requirements, and the work included.

2026 installed cost per roof square foot

Roof coveringTheRoofBill model range per roof sq ft
3-tab asphalt shingles$4–$6
Architectural asphalt shingles$5.21–$6.82
Class 4 impact-resistant shingles$6.50–$9.50
Corrugated metal$5–$10
Standing seam metal$10–$16
Concrete tile$10–$16
Clay tile$12–$18
Natural slate$15–$28
TPO / EPDM membrane$8.23–$10.54

These ranges are installed-covering planning inputs, not the full project total. Tear-off, disposal, permit, decking, flashing, ventilation, access, and roof geometry can change the estimate.

The short answer

Use the roof’s measured surface area, not the home’s interior floor area. Then compare the same material and project scope. The per-foot figure alone is not a complete replacement price.

Cost per roofing square (100 sq ft)

Roofers often quote per square, meaning 100 sq ft of roof. The table shows the model's installed rate per square, and the all-in cost per square once the other job lines are added, using the national baseline example: a 2,000 sq ft one-story footprint (2,240 sq ft of roof, 22.4 squares), medium pitch, simple gable, labor factor 1.00, one layer removed, the $300–$480 permit and disposal allowance and a 10% decking contingency.

Roof coveringInstalled rate per squareAll-in per square (national example)Example total, 22.4 squares
3-tab asphalt$400–$600$492–$734$11,000–$16,500
Architectural asphalt$521–$682$625–$825$14,000–$18,500
Class 4 impact-resistant shingles$650–$950$767–$1,119$17,200–$25,100
Corrugated metal$500–$1,000$613–$1,206$13,700–$27,000
Wood shake$800–$1,400$948–$1,651$21,200–$37,000
Standing seam metal$1,000–$1,600$1,163–$1,866$26,100–$41,800
Concrete tile$1,000–$1,600$1,173–$1,876$26,300–$42,000
Clay tile$1,200–$1,800$1,393–$2,096$31,200–$47,000
Natural slate$1,500–$2,800$1,723–$3,196$38,600–$71,600

"All-in" divides the full example total by 22.4 squares, so it includes tear-off, permits and the decking allowance. Tear-off assumes the old roof is the same material as the new one. When a quote says "$X a square," ask which of these two numbers it means.

What other 2026 guides report per square foot

Third-party guides usually publish one blended range across materials:

SourcePer square footNotes
Angi (2026 data)$4–$11All materials; national average job $9,530
Fixr (2026 data)$3.75–$11, average $4.75All materials; average job about $10,000
Fixr, metal roofing (2026 data)Average $11Metal only, materials and labor
TheRoofBill model, architectural shingles$5.21–$6.82 installed; $6.25–$8.25 all-inSingle material, line items shown above

A blended $4–$11 range spans everything from basic shingles to premium metal, so it can't tell you whether one material's quote is fair. Compare a quote with the rate for its material.

A simple example

Suppose a contractor measures 2,240 square feet of roof and quotes architectural shingles at $5.21–$6.82 per roof sq ft in the site’s base model. The covering portion is about $11,670–$15,280 before state labor adjustment, tear-off, permits, decking allowance, and optional details. This calculation illustrates how the unit rate works; it is not a local quote.

A “2,000-square-foot house” is not necessarily a 2,000-square-foot roof. The site’s example assumes a one-story 2,000-square-foot footprint, medium pitch, and simple gable; the slope adds area before the material rate is applied. Two houses with the same interior size can have very different roofs.

Why per-foot quotes differ

  • Roof measurement method and whether waste is included
  • Shingle grade, metal panel system, tile, or membrane specification
  • One or more existing layers to remove
  • Pitch, number of stories, hips, valleys, and penetrations
  • Decking repairs, flashing, ventilation, ice barrier, and permit scope
  • Local labor and disposal charges

Ask for both total price and measured roof area. A proposal that only says “$X per square” leaves out whether that means a 100-square-foot roofing square or a single square foot. Ask the roofer to define the unit and list exclusions.

Roof repair cost per square foot

Repairs are usually priced per job, not per square foot, because a vent boot or a few shingles takes the same setup as a larger patch. Per-square-foot repair pricing shows up mainly on larger areas and on tile: Fixr's tile repair data runs $8–$20 per sq ft for concrete tile, labor included. For job-level prices, see roof repair cost and tile roof repair cost.

Convert square feet to roofing squares

Divide measured roof area by 100: 2,240 sq ft ÷ 100 = 22.4 roofing squares before any material waste factor. If you only know the footprint, the roof pitch calculator gives the multiplier for your exact pitch. The contractor should explain how waste is calculated for the chosen product and roof layout.

Use the roof replacement cost calculator for a fuller scenario, follow the formula by hand in how to estimate roof replacement cost, and read our methodology to see what the model includes. For the labor portion alone, see roofing labor cost per square.

Sources and limits

Our installed ranges are 2026 planning estimates from the material model described in our methodology; per-square figures were calculated from it on November 16, 2026. Third-party per-foot ranges were checked the same day as linked above. We also compare Homewyse roofing installation cost data, Angi’s 2026 roof replacement guide, Fixr’s roof replacement guide, and BLS roofer wage data. These sources measure different scopes, so we use them as planning inputs, not as a single quote database or a guarantee. Check current local bids and the product manufacturer’s specifications before choosing a roof.

Compare other projects and materials in our 2026 roof cost guides.

The next step

Get your number in 60 seconds.

Answer a few quick questions and get an itemized 2026 estimate for your roof. No email, no sales calls.

Open the Roof Cost Calculator →

Based on 2026 public cost data. See the methodology.

Frequently asked questions

What is the average roof replacement cost per square foot in 2026?

There is no single useful average without the roof material and scope. TheRoofBill model ranges from $4–$6 per roof sq ft for 3-tab shingles to $15–$28 for natural slate, before separately modeled tear-off and other project items.

Is roofing square footage the same as my home’s square footage?

No. Roof area changes with slope, overhangs, porches, dormers, and roof shape. Ask for a roof measurement or diagram; do not multiply living area by a national per-foot number and treat it as a quote.

How much does roofing cost per square?

In TheRoofBill's 2026 model, architectural shingles are $521–$682 per square (100 sq ft) installed, or about $625–$825 per square all-in once one-layer tear-off, permits and a 10% decking allowance are added on a typical 22-square roof. 3-tab runs about $492–$734 per square all-in and standing seam metal about $1,163–$1,866.

What do other guides say roofing costs per square foot?

Angi's 2026 data puts roof replacement at $4–$11 per square foot across materials, and Fixr's 2026 guide gives an average of $4.75 with most jobs $3.75–$11. These are blended figures; compare them with a single material's rate, not with your total.

What is a roofing square?

One roofing square is 100 square feet of roof surface. Contractors commonly use squares for material quantities and some tear-off charges.

Cost figures are planning estimates based on 2026 public data (Homewyse, Angi, Fixr, BLS). They are not contractor quotes. Full disclaimer · How we calculate.