Calculator · 2026

Roof Pitch Calculator

Roof pitch is the rise in inches for every 12 inches of horizontal run, written as X/12. A 6/12 roof rises 6 inches per foot, which is a 26.57° angle and adds about 11.8% to the roof area compared with the flat footprint. Enter any two measurements below to get the pitch, angle and multiplier.

Calculator

Find your roof pitch

01

What do you know?

02

Units

Rise and run use the same unit, so the pitch doesn't depend on which one you pick.

03

Rise (inches)

How far the roof goes up.

04

Run (inches)

How far it goes across, measured level. 12 inches gives the rise straight as X/12.

+

Footprint area (optional, sq ft)

The flat area under the roof. Multiplied by the pitch multiplier, it gives the sloped roof area.

Your roof pitch

6/12

Exact: 6.00/12 · Conventional

Angle26.57°
Area multiplier1.118
Slope50.0%
Roof pitch triangleA right triangle showing run along the bottom, rise on the right and the roof angle at the lower left: 6/12 pitch, 26.57 degrees.Run 12Rise 626.57°

What is roof pitch?

Pitch is how many inches a roof rises for every 12 inches it runs horizontally, written X/12 (sometimes X:12). A 6/12 roof climbs 6 inches over each foot of level distance. Roofers, building codes and material instructions all use this form.

Slope is the same ratio as a percentage: rise divided by run, times 100. A 6/12 roof has a 50% slope. Codes sometimes state minimums this way, so it helps to convert between the two.

Angle is the pitch measured in degrees from horizontal. It’s what a digital level or phone app reads. You get it with the arctangent of rise ÷ run, so a 6/12 roof sits at 26.57°.

Roof pitch chart

The area multiplier is how much larger the sloped roof surface is than the flat area under it.

PitchAngleSlopeArea multiplier
1/124.76°8.3%1.003
2/129.46°16.7%1.014
3/1214.04°25.0%1.031
4/1218.43°33.3%1.054
5/1222.62°41.7%1.083
6/1226.57°50.0%1.118
7/1230.26°58.3%1.158
8/1233.69°66.7%1.202
9/1236.87°75.0%1.250
10/1239.81°83.3%1.302
11/1242.51°91.7%1.357
12/1245.00°100.0%1.414
14/1249.40°116.7%1.537
16/1253.13°133.3%1.667
18/1256.31°150.0%1.803

How to measure roof pitch

You need two numbers, rise and run, or one angle. Any of these three methods gets you there.

From the attic

Hold a level horizontally against the underside of a rafter, mark 12 inches along the level, and measure straight up from that mark to the rafter. That distance in inches is your rise per 12 inches of run, so 6 inches means a 6/12 pitch. Use a straight rafter, not one that sags, and stand on the joists, not the drywall between them.

From the roof

Rest one end of a 12-inch level on the roof surface, hold it level, and measure from its free end straight down to the roof. That distance is the rise over 12 inches. Only go on a roof if it's safe; otherwise measure from the attic or a ladder at the gable.

From the ground

Hold a pitch gauge or a phone level app against the roof edge at a gable end, or photograph the gable straight on and measure the roof line's angle. Enter the angle in the calculator’s Angle tab. Ground methods are less precise, so round to the nearest half pitch and confirm before you order materials.

How pitch changes roof area and cost

A sloped roof has more surface than the footprint under it. Multiply the footprint by the pitch multiplier to get the roof area. For example, a 2,000 sq ft footprint at 6/12: 2,000 × 1.118 = 2,236 sq ft, or about 22.4 roofing squares. Overhangs, porches and dormers add more, which is why a roofer measures the actual roof.

Steeper roofs also cost more for labor. Above walkable pitches, crews need roof jacks, harnesses and more time per square. Our cost model raises the installed cost line by 25% for 7/12–9/12 roofs and by 60% for 10/12 and steeper, on top of the extra area. See the roof replacement cost for your pitch, or count materials with the shingle calculator to see how many shingles you need.

Which roofing materials work on low-slope roofs?

Most asphalt shingles need a minimum slope. The International Residential Code (Section R905.2.2) allows asphalt shingles only on roofs of 2/12 or steeper, and requires a double layer of underlayment from 2/12 up to 4/12. Below 2/12, roofs typically use membranes such as TPO, EPDM or modified bitumen, which are sealed rather than shingled so water can’t back up under the laps. Local codes and the product’s installation instructions can be stricter. For pricing, see flat roof replacement cost and TPO roofing cost.

Common roof pitches on US homes

Most pitched roofs on US houses fall in the conventional range, roughly 4/12 to 9/12. That range is steep enough to shed rain and snow, and still walkable enough to install. Lower pitches show up on ranch houses, porches and additions. Steeper ones are typical of styles with tall gables and of heavy-snow regions. Pitch varies with region, era and architecture, so measure yours rather than assume.

Related tools

Frequently asked questions

What is a 6/12 roof pitch in degrees?

A 6/12 roof pitch is 26.57 degrees. The roof rises 6 inches for every 12 inches of horizontal run, a 50% slope, and the arctangent of 6 ÷ 12 is 26.57°. Its area multiplier is 1.118, so the sloped roof is about 11.8% larger than the flat footprint under it.

What is the most common roof pitch?

There isn't one official answer, but most pitched roofs on US houses fall in the conventional range of roughly 4/12 to 9/12. That range is walkable enough to install and steep enough to shed water. Low-slope sections are common on porches and additions. Measure your own roof rather than assume.

How do I calculate roof pitch?

Measure the rise over a 12-inch horizontal run. The rise in inches is your pitch, so 5 inches of rise is a 5/12 pitch. For any other run, divide rise by run and multiply by 12. If you have an angle instead, pitch equals 12 times the tangent of the angle.

What is a roof pitch multiplier?

It's the factor that converts flat footprint area into sloped roof area: the square root of 1 plus (rise ÷ run) squared. A 6/12 roof's multiplier is 1.118, so a 2,000 sq ft footprint has about 2,236 sq ft of roof before overhangs. Steeper roofs have larger multipliers.

Is a 4/12 roof pitch good for shingles?

Yes. The International Residential Code allows asphalt shingles on roofs of 2/12 and steeper. From 2/12 up to 4/12 it requires a double layer of underlayment, so at 4/12 a standard single layer is allowed. Local codes and the shingle manufacturer's instructions can be stricter, so check both.

Cost figures are planning estimates based on 2026 public data (Homewyse, Angi, Fixr, BLS). They are not contractor quotes. Full disclaimer · How we calculate.