Cost Guides · 2026

TPO Roofing Cost in 2026

TPO roofing costs per square foot installed in 2026, by membrane thickness, insulation and tear-off. Compare TPO vs EPDM vs modified bitumen for flat roofs.

$4–$14

Short answer

TPO roofing costs per square foot installed in 2026, by membrane thickness, insulation and tear-off. Compare TPO vs EPDM vs modified bitumen for flat roofs.

Calculator

Roof cost calculator

Preset to the national labor baseline and a 2,000 sq ft home (2,240 sq ft of roof). Change any input for an itemized 2026 estimate. The link in your address bar saves your inputs.

01

Material

Model rate: $8.23–$10.54 per roof sq ft installed.

02

Roof area

Area unit

Roof surface, not floor area. One roofing square = 100 sq ft. 2,240 sq ft = 22.4 squares.

03

Roof pitch

Steeper roofs take more labor and safety setup.

04

Complexity

05

Stories

06

Old layers to tear off

Tear-off: $40–$60 per square per layer.

07

Location

State labor factor from BLS roofer wages. ZIP is optional and never stored.

+

Extras (optional)

Itemized planning estimate

Your roof bill

National baseline · 2,240 sq ft roof

Planning estimate
Materials & installation2,240 sq ft × $8.23–$10.54 × 1.00 adjustments$18,430–$23,610
Tear-off22.4 squares × $40–$60 × 1 layer$890–$1,350
Permits & disposalModel default, scaled to 1.6× at the high end$300–$480
Decking contingency10% of base, for damaged decking found mid-job$1,840–$2,370

Estimated installed total · TPO / EPDM Flat Membrane

$21.4k–$27.8k
Low$21,500
Typical (midpoint)$24,600
High$27,800

$960–$1,240 per roofing square, all in. Planning life 20–30 years.

Not included: gutters and structural repairs beyond decking.

Planning estimate only, not a contractor quote. Actual cost depends on roof condition, local requirements, and the work included.

TPO roofing cost: quick answer

TPO roofing costs about $4–$14 per square foot installed. Fixr and Angi both put it at $4–$14, and HomeGuide at $4–$10, with an average residential job near $11,200 ($7,700–$14,000). TheRoofBill's model uses $8.23–$10.54 for a TPO or EPDM membrane, which is where the flat roof cost calculator starts. The typical job is tearing off an old low-slope roof over a porch, addition or flat-roof house and installing a mechanically fastened membrane over new insulation.

TPO roofing cost breakdown

ItemTypical cost per sq ftSource
TPO membrane (material only)$1.00–$2.50HomeGuide
Installation labor$2.50–$4.50HomeGuide
Polyiso insulation, 1–3 inches$0.50–$3.00HomeGuide
Tear-off of the old roof$1.00–$2.00HomeGuide
Flashing at penetrations and curbs$200–$500 each areaHomeGuide
Installed total$4–$14Fixr; Angi; HomeGuide ($4–$10)

For whole-job sizes, HomeGuide puts 1,000 sq ft at $4,000–$10,000 and 2,000 sq ft at $8,000–$20,000.

What changes the price

  • Membrane thickness. 45 mil is the entry grade, 60 mil the common standard, and 80 mil the premium; thicker costs more and usually carries a longer warranty.
  • Attachment method. Ballasted (held down with stone) is cheapest, mechanically fastened is most common on homes, and fully adhered costs the most.
  • Insulation. Adding or replacing polyiso board, or tapering it to fix drainage, can add as much as the membrane.
  • Tear-off and deck repair. Removing old layers and replacing wet or rotted decking under them adds labor and disposal.
  • Edges and penetrations. Parapet walls, drains, vents, skylights and HVAC curbs each need welded flashing details.
  • Roof size and access. Small residential roofs cost more per square foot than large commercial ones, because setup is spread over less area.

TPO roofing cost by type

By thickness and attachment (membrane material per sq ft, HomeGuide):

Attachment45 mil60–75 mil
Ballasted$1.80–$2.30$2.00–$2.50
Mechanically fastened$2.00–$3.00$2.20–$3.10
Fully adhered$2.80–$3.20$3.00–$3.50

TPO vs EPDM vs modified bitumen (installed per sq ft):

MembraneFixrAngiNotes
TPO$4–$14$4–$14White, reflective, heat-welded seams
EPDM$4–$13$5–$13Black rubber, taped or glued seams
Modified bitumen (incl. torch-down)$4–$8$4–$8Asphalt-based rolls, often torch-applied
PVC$5–$16$5.25–$12.50Welded seams, resists grease and chemicals

The three main options overlap heavily on price. Pick on climate, building use and the installer's experience with the system.

How to check a TPO roofing quote

  • Thickness in mils. "TPO" alone isn't a spec. The quote should say 45, 60 or 80 mil and name the manufacturer.
  • Attachment and insulation. It should state fastened, adhered or ballasted, and the insulation type and thickness.
  • Tear-off and deck. Confirm whether the old roof is removed and how wet or rotted decking is priced.
  • Seams and details. Ask how seams are welded and tested, and how drains, edges and penetrations are flashed.
  • Warranty. Check both the manufacturer's membrane warranty and the installer's workmanship warranty, and what it takes to qualify.
  • Drainage. If water ponds today, the quote should say how the new roof will fix that, for example with tapered insulation or added drains.

Repair or replace?

A TPO roof with a few failed seams or punctures can usually be patched by heat-welding new membrane over the damage. Replace it when seams are failing across the roof, the insulation underneath is wet, or the membrane is brittle and chalky near the end of its life. A roof coating can extend a sound, dry membrane, but it doesn't fix wet insulation.

Sources and limits

SourceWhat it gave usDate
Fixr, flat roof installation costInstalled range per membraneUpdated January 27, 2026; checked November 13, 2026
Angi, flat roofing materialsInstalled range per membraneNo date shown; checked November 13, 2026
HomeGuide, TPO roofing costInstalled range, average total, thickness, insulation, tear-off, labor, lifespanNo date shown; checked November 17, 2026
TheRoofBill methodologyModel TPO/EPDM input, $8.23–$10.54 per sq ftNovember 2026

These are national planning ranges, not quotes. Residential flat roofs are small, so per-square-foot prices run higher than the commercial figures some sources quote.

The next step

Get your number in 60 seconds.

Answer a few quick questions and get an itemized 2026 estimate for your roof. No email, no sales calls.

Open the Roof Cost Calculator →

Based on 2026 public cost data. See the methodology.

FAQ

How much does a TPO roof cost per square foot?

Installed TPO typically costs about $4–$14 per square foot. Fixr and Angi both put it at $4–$14, HomeGuide at $4–$10, and TheRoofBill's model uses $8.23–$10.54 for a TPO or EPDM membrane. Thicker membranes, new insulation and tear-off push a job toward the top of the range.

Is TPO better than EPDM?

Neither wins everywhere. TPO is usually white and reflective, with heat-welded seams, which suits hot, sunny climates. EPDM is black rubber with taped or glued seams, often a little cheaper and long proven in cold climates. Installed prices overlap closely, so installer quality and the detailing matter more than the label.

How long does a TPO roof last?

HomeGuide puts typical TPO life at 10–25 years, and our model plans on 20–30 years for a TPO or EPDM membrane. Thicker membranes, fully welded seams, good drainage and regular inspections push it toward the long end. Ponding water and foot traffic shorten it.

Cost figures are planning estimates based on 2026 public data (Homewyse, Angi, Fixr, BLS). They are not contractor quotes. Full disclaimer · How we calculate.