Calculator · 2026

Flat Roof Cost Calculator

Torch down roofing costs about $5.64–$7.23 per sq ft installed in TheRoofBill’s 2026 model, below TPO and EPDM at $8.23–$10.54. A 1,000 sq ft flat roof with one layer torn off, permits and a decking allowance runs about $6,900–$9,000 at national labor rates. Choose your system and size below.

Calculator

Flat roof cost calculator

01

Material

Model rate: $5.64–$7.23 per roof sq ft installed.

02

Roof area

Area unit

Roof surface, not floor area. One roofing square = 100 sq ft. 1,000 sq ft = 10.0 squares.

03

Stories

04

Old layers to tear off

Tear-off: $40–$60 per square per layer.

05

Location

State labor factor from BLS roofer wages. ZIP is optional and never stored.

+

Extras (optional)

Itemized planning estimate

Your roof bill

National baseline · 1,000 sq ft roof

Planning estimate
Materials & installation1,000 sq ft × $5.64–$7.23 × 1.00 adjustments$5,640–$7,230
Tear-off10.0 squares × $40–$60 × 1 layer$400–$600
Permits & disposalModel default, scaled to 1.6× at the high end$300–$480
Decking contingency10% of base, for damaged decking found mid-job$560–$730

Estimated installed total · Torch-down modified bitumen

$6.9k–$9.1k
Low$6,900
Typical (midpoint)$8,000
High$9,000

$690–$900 per roofing square, all in.

Not included: insulation and tapered insulation, parapet and penetration flashing, drains and scuppers, and structural repairs beyond decking.

Planning estimate only, not a contractor quote. Actual cost depends on roof condition, local requirements, and the work included.

Flat roof prices by system

SystemTheRoofBill model, $/sq ftFixr 2026Angi1,000 sq ft, all in
Torch-down modified bitumen$5.64–$7.23$4–$8$4–$8$6,900–$9,000
TPO membrane$8.23–$10.54$4–$14$4–$14$9,800–$12,700
EPDM (rubber) membrane$8.23–$10.54$4–$13$5–$13$9,800–$12,700
PVC membrane$9.88–$12.65$5–$16$5.25–$12.5$11,600–$15,000
Built-up roof (BUR, tar and gravel)$6.58–$8.43$4–$10$4–$10$7,900–$10,400

The model’s TPO/EPDM rate comes from the same data as our flat roof replacement cost guide. The other systems are scaled from it using each system’s price relative to TPO and EPDM in Fixr’s 2026 ranges (midpoint to midpoint). Fixr and Angi do not price torch-down separately; it is one way of installing modified bitumen, so it uses the modified bitumen figures. All-in totals add one layer of tear-off at $40–$60 per square, permits and a 10% decking contingency.

Torch down roofing: pros and cons

  • Lower price: modified bitumen is the cheapest membrane in both Fixr’s and Angi’s ranges.
  • Tough surface: the multi-layer, granule-surfaced sheet tolerates foot traffic better than a single-ply membrane.
  • Familiar to repair: many residential roofers work with modified bitumen, so patches are easy to source.
  • Open flame: the sheets are heated with a propane torch, which carries a fire risk at wood decks, eaves and wall joints.
  • Dark surface: unless a reflective cap sheet or coating is used, it runs hotter than white TPO or PVC.

Fire safety and permits for torch-applied roofing

Torching is hot work. Many fire departments apply hot-work rules to it, which commonly include keeping an extinguisher on the roof and watching for smoldering material after the torch goes out. Some building owners, HOAs and insurers restrict torching near combustible walls or on attached homes. Ask the roofer how they detail torch-sensitive areas, whether they switch to self-adhered sheets there, and whether a separate hot-work permit applies along with the reroof permit.

Flat roof cost by size

Roof areaTorch-downTPO / EPDMPVC
500 sq ft$3,600–$4,800$5,000–$6,600$5,900–$7,700
1,000 sq ft$6,900–$9,000$9,800–$12,700$11,600–$15,000
1,500 sq ft$10,200–$13,300$14,500–$18,800$17,200–$22,300
2,000 sq ft$13,500–$17,600$19,200–$24,900$22,800–$29,500

Examples assume one story, one layer of tear-off and national labor rates (factor 1.00). Use the calculator’s state field for local labor; in New York (1.19×) the installed rate runs 19% above the national baseline.

Related guides

Frequently asked questions

How much does torch down roofing cost in 2026?

About $5.64–$7.23 per sq ft installed in TheRoofBill's model. With one layer of tear-off, permits and a 10% decking allowance, a 1,000 sq ft flat roof comes to about $6,900–$9,000 at national labor rates.

How does this flat roof cost calculator work?

Pick a system, enter the roof area in square feet or squares, then stories, tear-off layers and state. The calculator applies the installed rate and the state labor factor, then adds tear-off, permits and a decking contingency, and shows each line.

Is torch down cheaper than TPO or EPDM?

Usually. Fixr and Angi both put modified bitumen at $4–$8 per sq ft against $4–$14 for TPO and $4–$13 (Fixr) or $5–$13 (Angi) for EPDM. Our model prices torch-down at about 31% below its TPO/EPDM rate.

How much does a flat roof replacement cost?

For a 1,500 sq ft flat roof with one layer torn off at national labor rates, the model gives about $10,200–$13,300 for torch-down and $14,500–$18,800 for TPO or EPDM.

Does torch down roofing need a permit?

A reroof generally needs a building permit, and torch-applied roofing uses an open flame, so many fire departments treat it as hot work with its own rules, such as a fire watch after torching. Ask your building department and confirm the contractor carries insurance that covers torch work.

Does the calculator include insulation, parapets or tapered insulation?

No. None of the sources on our methodology page publishes a reliable unit price for polyiso by thickness, tapered insulation, parapet flashing or penetrations, so we leave them out rather than guess. Ask for each as a separate line item.

How long does a flat roof last?

Our model uses 20–30 years for TPO and EPDM membranes. We have not yet sourced comparable planning lives for torch-down, PVC or built-up roofs, so the calculator does not show one for those systems.

Cost figures are planning estimates based on 2026 public data (Homewyse, Angi, Fixr, BLS). They are not contractor quotes. Full disclaimer · How we calculate.