Costs by State · 2026

Roof Replacement Cost in Washington State (2026)

Washington State roof replacement in 2026: $15,100–$20,000 in our 2,000 sq ft shingle model, plus L&I rules, moss, wildfire roofing and Seattle permits.

Ranked #11 of 51 in the TheRoofBill Roof Replacement Cost Index

Modeled planning range$15.1k–$20.0k
Example roof area2,240 sq ft
State labor factor1.09×

Calculator

Roof cost calculator

Preset to Washington’s labor factor (1.09×) and a 2,000 sq ft home (2,240 sq ft of roof). Change any input for an itemized 2026 estimate. The link in your address bar saves your inputs.

01

Material

Model rate: $5.21–$6.82 per roof sq ft installed.

02

Roof area

Area unit

Roof surface, not floor area. One roofing square = 100 sq ft. 2,240 sq ft = 22.4 squares.

03

Roof pitch

Steeper roofs take more labor and safety setup.

04

Complexity

05

Stories

06

Old layers to tear off

Tear-off: $39–$53 per square per layer.

07

Location

State labor factor from BLS roofer wages. ZIP is optional and never stored.

+

Extras (optional)

Itemized planning estimate

Your roof bill

Washington · 2,240 sq ft roof

Planning estimate
Materials & installation2,240 sq ft × $5.21–$6.82 × 1.09 adjustments$12,720–$16,660
Tear-off22.4 squares × $39–$53 × 1 layer$870–$1,190
Permits & disposalModel default, scaled to 1.6× at the high end$300–$480
Decking contingency10% of base, for damaged decking found mid-job$1,270–$1,670

Estimated installed total · Architectural Asphalt Shingles

$15.1k–$20.0k
Low$15,200
Typical (midpoint)$17,600
High$20,000

$680–$890 per roofing square, all in. Planning life 25–30 years.

Not included: gutters and structural repairs beyond decking.

Planning estimate only, not a contractor quote. Actual cost depends on roof condition, local requirements, and the work included.

What a new roof costs in Washington in 2026

TheRoofBill's 2026 model puts architectural asphalt shingles at $15,100–$20,000 for a one-story house with a 2,000 sq ft footprint, medium pitch, a simple gable and one layer of old roofing torn off. Treat that as a planning range. It is not an average of Washington invoices, and it is not a bid.

The model applies a Washington labor factor of 1.09, meaning installed labor runs above the national baseline. That factor is built from BLS wage data for roofers, so it reflects pay, not every cost a Washington contractor carries. Our methodology shows the formula and where it can be wrong.

Here is how home size moves the shingle price, with the same assumptions. All figures are TheRoofBill 2026 model outputs.

Home footprintWashington model, architectural shingles (2026)
1,500 sq ft$11,400–$15,200
2,000 sq ft$15,100–$20,000
2,500 sq ft$18,800–$24,900
3,000 sq ft$22,500–$29,800

Shape matters as much as size. Build that same 2,000 sq ft footprint as a two-story home with a steep hip roof and the model returns $24,200–$31,900 in architectural shingles, because there is more roof surface, more cutting and slower, harnessed work.

Washington roof prices by material

Material choice is the other big lever. The model prices the 2,000 sq ft one-story example this way:

Roof coveringWashington model, 2,000 sq ft home (2026)
3-tab asphalt shingles$11,900–$17,800
Architectural asphalt shingles$15,100–$20,000
Stone-coated steel$22,900–$40,000
Wood shake$23,000–$40,100
Standing seam metal$28,200–$45,400
Concrete tile$28,500–$45,600

Two Washington realities should shape that choice. On the wet west side, moss and shade wear on roofs year after year. On the dry east side and in forested foothills, fire exposure can make wood shake a poor fit no matter its price. Both are covered below. For metal specifically, see our metal roof cost guide.

Checking a roofer's L&I registration

Washington does not issue a roofing license by exam. Instead, every contractor must register with L&I, and roofing is one of the specialty categories. A specialty contractor can only do work in the specialty it is registered for. To register, a specialty contractor needs a $15,000 surety bond (general contractors need $30,000) and liability insurance of at least $250,000 combined single limit, or $200,000 public liability plus $50,000 property damage. L&I raised the bond amounts as of July 1, 2024, so older articles quoting smaller bonds are out of date.

Before you sign, look the company up with L&I's Verify a Contractor tool. You can search by business or owner name, UBI number or registration number. The record shows whether the registration is active, the bond and insurance on file, any lawsuits against the bond, and safety violations. L&I is clear about the limits: a clean record means the contractor posted the minimum bond, bought liability insurance and has not been suspended. It says nothing about workmanship, so you still need references and a written scope.

A $15,000 bond does not go far on a $30,000 roof. That is one reason to check the record yourself and keep payments tied to progress.

The disclosure statement and lien risk

Washington law adds a step most homeowners never hear about. Under RCW 18.27.114, a contractor working on a home of four or fewer units must give you a written disclosure statement before starting any job of $1,000 or more. Nearly every reroof qualifies. The contractor keeps a signed copy for three years, and one who never delivered it cannot bring a lien claim on that contract. L&I publishes a model version of the form showing the registration number, bond amount and expiration date.

The statement exists because of liens. L&I's guide to liens warns that suppliers and subcontractors who go unpaid can look to your property for payment even if you paid your roofer in full. Its suggestions: make checks payable jointly to the contractor and the supplier, and get signed lien releases from major suppliers before the final payment. A roofing job involves a big shingle or metal delivery, so ask who the supplier is.

Moss, shade and wet winters on the west side

Western Washington roofs rarely fail from one dramatic storm. More often, moss and shade do slow damage. WSU Extension's demossing study manual says uncontrolled moss shortens a roof's life, and it recommends cutting back overhanging branches, removing as much moss as possible, and treating with a labeled product. It also says zinc-galvanized or copper flashing and ridge strips control moss when they sit roughly 10 to 15 feet down from the ridge.

There is a tradeoff. A WSU-linked study of roofing runoff found that rain slowly dissolves metal from metal and metal-coated roofing, which ends up in stormwater. Weigh that before adding zinc strips over a garden or near a creek.

At replacement time, ask whether the bid includes algae-resistant shingles, new ridge and soffit vents, and a plan for any rotted sheathing around valleys and eaves. Poor airflow traps moisture under the deck in long, damp winters; our roof ventilation guide explains how to check the numbers. Afterward, a yearly cleaning on the roof maintenance checklist helps the new roof reach its rated life.

Wildfire and snow on the east side

East of the Cascades, and in wooded areas on both sides, fire is the bigger roof question. The Department of Natural Resources' Wildfire Ready plan calls the roof the most vulnerable part of a home and calls a wood roof an extreme danger that should be replaced with Class A fire-rated materials. DNR's home preparation guide lists tile, slate and asphalt with an underlayment as Class A options. If you live in a wildland area, ask any bidder to state the fire classification of the full roof assembly in writing, and price shake against a Class A shingle or metal before choosing.

Snow loads are set locally and can change from one parcel to the next. Chelan County's building division says snow loads are site-specific and that the county will provide both ground and roof snow loads for a parcel. Spokane County lists a basic minimum roof snow load of 30 psf. This matters most when switching to a heavier covering such as concrete tile. Ask whether the existing framing has been checked for the new weight plus local snow.

Permits in Seattle and elsewhere

Permit rules vary by city and county. In Seattle, the Department of Construction and Inspections says a re-roof of a one- or two-family home or townhouse does not need a permit when the only change to the building envelope is adding or replacing insulation at an equal or better value. Any other change to the envelope needs a construction permit. SDCI also notes that energy code insulation must be added when existing roof sheathing or insulation is exposed or the roof cavities are uninsulated, which can add cost once tear-off reveals the deck. Outside Seattle, call the building department for the address and get the answer, plus who pulls any permit, into the contract.

Storm claims and the Insurance Commissioner

Windstorms and falling trees cause many Washington roof claims. After damage, the Office of the Insurance Commissioner advises calling your insurer quickly, photographing the damage, covering leaks with a tarp if it is safe, and keeping receipts. You have the right to choose your own contractor. Insurers are not required to send an adjuster, but the OIC's claims guide says they should inspect within 30 days of the claim date.

Be careful if a roofer asks you to sign an assignment of benefits. The OIC warns that it hands control of the claim to the contractor, who then deals directly with your insurer, and that these contracts usually lack a cooling-off period. You can file the claim yourself.

Costs by region

Questions to ask a Washington roofer

  1. What is your L&I registration number, and will you give me the disclosure statement before work starts?
  2. What is the measured roof area, and can I see the diagram?
  3. Which product, underlayment, flashing and ventilation are included?
  4. What is the per-sheet price for replacing rotted decking, and will you ask first?
  5. Is a permit or energy code insulation required at this address, and who handles it?
  6. Who is the material supplier, and will you provide lien releases before final payment?

Run your own roof through the roof replacement cost calculator, compare with roof replacement costs in other states, or browse the national 2026 roof cost guides.

The next step

Get your number in 60 seconds.

Answer a few quick questions and get an itemized 2026 estimate for your roof. No email, no sales calls.

Open the Roof Cost Calculator →

Based on 2026 public cost data. See the methodology.

Sources: TheRoofBill 2026 cost model; BLS OEWS May 2025; Washington State Department of Labor and Industries; RCW 18.27.114; Washington Office of the Insurance Commissioner; Washington Department of Natural Resources; WSU Extension; Seattle Department of Construction and Inspections; Chelan County; Spokane County. Checked October 2026.

The next step

Get your number in 60 seconds.

Answer a few quick questions and get an itemized 2026 estimate for your roof. No email, no sales calls.

Open the Roof Cost Calculator →

Based on 2026 public cost data. See the methodology.

Frequently asked questions

How much does a new roof cost in Washington in 2026?

TheRoofBill's 2026 model estimates $15,100–$20,000 for a one-story home with a 2,000 sq ft footprint, medium pitch, simple gable, architectural asphalt shingles and one layer of tear-off. Standing seam metal on the same house models at $28,200–$45,400. These are model outputs, not a survey of Washington quotes.

Does a roofer need a license in Washington?

Washington registers contractors through the Department of Labor and Industries (L&I) rather than licensing them by exam. Roofing is a specialty registration. A specialty contractor must carry a $15,000 bond and liability insurance of at least $250,000 combined single limit, or $200,000 public liability plus $50,000 property damage. You can check any contractor with L&I's Verify a Contractor tool.

What is the contractor disclosure statement in Washington?

Under RCW 18.27.114, a contractor working on a home of four or fewer units must give the customer a written disclosure statement before starting any job of $1,000 or more. It explains lien rights and shows the contractor's registration and bond. A contractor who skips it cannot bring a lien claim on that contract.

Do I need a permit to reroof a house in Seattle?

Usually not. Seattle's Department of Construction and Inspections says a re-roof of a one- or two-family home or townhouse does not need a permit if the only change to the building envelope is adding or replacing insulation with an equal or better value. Other envelope changes need a construction permit, and other cities set their own rules.

How long does my insurer have to inspect roof damage in Washington?

The Office of the Insurance Commissioner says insurers are not required to send an adjuster, but should inspect the damage within 30 days of the date you filed the claim. Some insurers use photos or a virtual inspection instead.

Cost figures are planning estimates based on 2026 public data (Homewyse, Angi, Fixr, BLS). They are not contractor quotes. Full disclaimer · How we calculate.