Contractor Guides · 2026

How Many Shingles Do I Need? (2026): Bundles, Squares & Waste

Most shingles come 3 bundles per square (100 sq ft). Convert footprint to roof area, add 10–15% waste, then count starter, ridge cap and underlayment.

Short answer

Most shingles come 3 bundles per square (100 sq ft). Convert footprint to roof area, add 10–15% waste, then count starter, ridge cap and underlayment.

How many shingles do I need? The short answer

Most asphalt shingles are packed 3 bundles per square, where a square is 100 sq ft of roof surface. To count bundles: find your roof area, divide by 100, add a waste factor (about 10% for a simple gable, more for hips and valleys) and multiply by 3. Round up; suppliers don't split bundles. Prefer to skip the arithmetic? The roof shingle calculator runs these steps for you.

The short answer

A 60×30 ft house with a 6/12 gable roof has about 2,012 sq ft of roof. With 10% waste that's about 22.1 squares, or 67 bundles of field shingles, plus about 2 bundles of starter, 3 bundles of ridge cap and 3 rolls of underlayment. The worked example below shows every step.

Step 1: Measure the roof

You need roof area, not living area. Three ways to get it, from rough to exact:

  1. From the ground: measure the footprint (outside length × width, including overhangs if you can) and multiply by the slope factor in step 2.
  2. Plane by plane: for each rectangular roof plane, multiply eave length by rafter length (eave to ridge, measured along the slope), then add the planes.
  3. A measurement report: satellite or drone reports list each plane's area plus ridge, hip, valley, eave and rake lengths, which you'll need for accessories.

Stay off the roof unless you're trained and equipped for it. Our roofing square guide covers the unit.

Step 2: Convert footprint to roof area

Multiply the footprint by the slope factor for your pitch (rise in inches per 12 inches of run):

PitchSlope factor
3/121.031
4/121.054
6/121.118
8/121.202
10/121.302
12/121.414

These are the exact geometric factors (√(1 + (rise/12)²)). TheRoofBill's cost model rounds them into bands (1.04, 1.12, 1.25, 1.40) for pricing; for ordering material, use the exact factor.

Step 3: Convert to squares and add waste

Squares = roof area ÷ 100. Then multiply by (1 + waste). GAF's roofing shopping worksheet says to always add a 10% waste factor. For more complex roofs, Vertigraph's guide to roofing squares suggests:

Roof typeWaste factor
Simple gable, no hips or valleys10%
One or two hips or valleys12%
Hip-and-valley roof, several intersections15%
Cut-up roof: dormers, skylights, intricate intersections18–20%

Step 4: Squares to bundles

Bundles = squares (with waste) × bundles per square, rounded up. Three per square is standard: GAF's Timberline AS II specifications, for example, list 3 bundles and 64 pieces per square, and GAF's worksheet divides by 33.33 sq ft per bundle. Some thicker designer shingles cover less per bundle, so check the wrapper before you order.

Step 5: Count the accessories

Field shingles are only part of the order. GAF's worksheet counts accessories by length or area:

ItemMeasureCoverage (GAF worksheet)
Starter strip (Pro-Start)Eaves + rakes, lineal feet120 lin ft per bundle
Hip and ridge cap (Seal-A-Ridge)Hips + ridges, lineal feet25 lin ft per bundle
Synthetic underlaymentSquares10 squares per roll
Ice and water barrierEaves (and valleys) where requiredPer roll; see underlayment cost
Drip edgeEaves (and rakes, where used), lineal feetBy piece length
Ridge ventRidge, lineal feet4 lin ft per piece for rigid vents

Coverage differs by product line: other GAF starter and ridge products in the same worksheet cover 33 or 20 lineal feet per bundle or box. Nails are counted per square from the shingle's instructions; GAF lists 256 per square for Timberline AS II.

Worked example: 60×30 ft gable at 6/12

LineCalculationResult
Roof area1,800 sq ft footprint × 1.1182,012 sq ft
Squares2,012 ÷ 10020.12
Squares with waste20.12 × 1.10 (simple gable)22.14
Field shingle bundles22.14 × 3, rounded up67 bundles
Eave length2 eaves × 60 ft120 lin ft
Rake length4 rakes × (15 ft run × 1.118)67 lin ft
Starter bundles(120 + 67) ÷ 120, rounded up2 bundles
Ridge cap bundles60 ft ridge ÷ 25, rounded up3 bundles
Underlayment rolls22.14 squares ÷ 10, rounded up3 rolls

The same footprint as a hip roof at 15% waste needs about 20.12 × 1.15 × 3 = 70 bundles of field shingles, plus more ridge cap for the four hips. Overhangs aren't included here; add them if you measured the walls rather than the roof edge.

From quantity to cost

Material quantity is only part of a roof's price; labor, tear-off, disposal and permits usually outweigh it. For an installed estimate on the same house, see how to estimate roof replacement cost or run the roof replacement cost calculator. Asphalt shingle roof cost compares installed prices by shingle type.

Ordering tips

  • Order whole bundles and keep the same color lot for the whole roof; ask the supplier about returning unopened bundles.
  • Keep a bundle or two for future repairs, if your supplier's return policy allows.
  • If a roofer is doing the job, compare their squares count with yours. A difference of more than a few squares is worth a question before you compare prices.
  • Doing the work yourself? Read DIY vs hiring a pro first.

The next step

Get your number in 60 seconds.

Answer a few quick questions and get an itemized 2026 estimate for your roof. No email, no sales calls.

Open the Roof Cost Calculator →

Based on 2026 public cost data. See the methodology.

Sources and fact-check date

Checked November 15, 2026:

More step-by-step help is in our contractor guides.

The next step

Get your number in 60 seconds.

Answer a few quick questions and get an itemized 2026 estimate for your roof. No email, no sales calls.

Open the Roof Cost Calculator →

Based on 2026 public cost data. See the methodology.

Frequently asked questions

How many bundles of shingles do I need per square?

Usually three. GAF's own spec for Timberline AS II, for example, lists 3 bundles and 64 pieces per square, and its shopping worksheet divides shingle area by 33.33 sq ft per bundle. Some heavier designer shingles pack fewer square feet per bundle, so always read the coverage printed on the wrapper.

How do I calculate how many shingles I need?

Multiply your footprint by the slope factor for your pitch to get roof area, divide by 100 for squares, add a waste factor (GAF's worksheet says always add 10%; hip and cut-up roofs need more), then multiply by bundles per square and round up. A 60×30 ft gable at 6/12 needs about 67 bundles at 10% waste.

What waste factor should I use for shingles?

About 10% for a simple gable. Vertigraph, an estimating-software maker, suggests 12% for one or two hips or valleys, 15% for hip-and-valley roofs and 18–20% for cut-up roofs with dormers and skylights. More cuts mean more offcuts too small to reuse.

Do I need separate starter and ridge cap shingles?

Most manufacturers sell them separately and count them in their system warranties. In GAF's worksheet, Pro-Start starter covers about 120 lineal feet per bundle along eaves and rakes, and Seal-A-Ridge covers 25 lineal feet per bundle along hips and ridges. Field shingles are counted from roof area alone.

Cost figures are planning estimates based on 2026 public data (Homewyse, Angi, Fixr, BLS). They are not contractor quotes. Full disclaimer · How we calculate.