How much does a metal roof cost in Florida in 2026?
TheRoofBill's 2026 model puts a corrugated metal roof at $12,000–$23,600 and a standing seam roof at $22,600–$36,300 for a defined Florida example: a one-story home with a 2,000 sq ft footprint, medium pitch, simple gable and one layer of tear-off. The model starts from installed planning inputs of $5–$10 per roof sq ft for corrugated and $10–$16 for standing seam, then applies Florida's 0.86× labor factor, a planning estimate built from BLS wage data for roofers. These are model outputs, not a survey of Florida bids, and they do not price HVHZ engineering or premium coastal metals.
| Home footprint | Corrugated metal (2026 model) | Standing seam (2026 model) |
|---|---|---|
| 1,500 sq ft | $9,000–$17,900 | $17,000–$27,400 |
| 2,000 sq ft | $12,000–$23,600 | $22,600–$36,300 |
| 2,500 sq ft | $14,900–$29,400 | $28,100–$45,300 |
A footprint is not the roof area. Overhangs, porches and pitch add surface, so ask every bidder for the measured roof area in squares.
Be honest with yourself about the high end. Homewyse's 2026 standing-seam calculator runs noticeably higher than our model range, as our national metal roof cost guide notes. Treat these Florida figures as the lower end of planning and let local bids set the real number.
The short answer
Metal vs. shingles vs. tile in Florida
The same model assumptions (2,000 sq ft footprint, one story, medium pitch, simple gable, one layer of tear-off) for the other common Florida roofs:
| Roof covering | Florida example, 2,000 sq ft (2026 model) |
|---|---|
| Architectural asphalt shingles | $12,200–$16,200 |
| Corrugated metal | $12,000–$23,600 |
| Stone-coated steel | $18,300–$32,100 |
| Standing seam metal | $22,600–$36,300 |
| Concrete tile | $22,800–$36,600 |
Corrugated metal overlaps shingles at the low end, but its range is wider because panel gauge, profile and trim vary so much. Standing seam lands close to concrete tile. Our model's broad planning lives are 30–45 years for corrugated and 40–70 for standing seam; those are not warranties, so compare lifecycle cost only after you have like-for-like bids.
Corrugated vs. standing seam: what you are paying for
Corrugated and other exposed-fastener panels (including the 5V crimp and ribbed profiles common in Florida) are screwed through the face of the panel into the deck or purlins. They cost less and install faster, but every screw and washer is a potential leak point and a maintenance item over time.
Standing seam panels attach with concealed clips under raised seams, which lets the metal move with heat and keeps fasteners out of the weather. The extra cost comes from roll-forming, clips, seaming and more detailed trim. Florida approvals spell out those details: one Miami-Dade NOA for a steel standing seam system requires a full 90-degree single-lock seam, while another aluminum standing seam NOA specifies a 180-degree double-lock seam. A bid that substitutes a different seam or clip spacing may not match the approval.
To price standing seam on your own roof with Florida's labor factor, use the standing seam metal roof cost calculator and pick Florida as the location.
Stone-coated steel looks like shingle or tile and sits between the two in our model. It still needs its own approval and compatible accessories.
Florida product approval and Miami-Dade NOAs for metal roofs
Florida Product Approval evaluation reports file metal panels under Roofing, subcategory Metal Roofing, and each report is scoped to a code edition and to either HVHZ or non-HVHZ use. For example, one aluminum mechanical-seam panel report is written for HVHZ use, while a 26-gauge PBR panel report is non-HVHZ. Ask for the FL number of the exact panel, deck and fastening combination being quoted, and check that it covers the current code edition.
In Miami-Dade and Broward, the High-Velocity Hurricane Zone, expect a Miami-Dade Notice of Acceptance. Metal NOAs list a design pressure for each assembly, and those vary widely: one 2019 system is rated around -86 psf and another 2019 system around -161 psf. NOAs also carry expiration dates and tie valleys and flashing to Roofing Application Standard RAS 133, as in this 2025 steel panel NOA. Higher-rated assemblies usually mean closer clip spacing, more fasteners and more labor, which is one reason HVHZ metal bids run high.
FEMA's Hurricane Michael best-practices report recommends verifying that metal panel systems were tested to the appropriate wind pressures (it cites ASTM E1592 and ASCE 7-16). It also observed that metal roofs on buildings built to the Florida Building Code appeared to perform better than other coverings, while still documenting metal roof damage. No metal roof is hurricane-proof.
For permits, the 25% rule and general licensing, see our Florida roof replacement cost guide.
Salt air, fasteners and corrosion
Coastal exposure changes the material list, and the price.
- Fasteners. FEMA's Technical Bulletin 8 on coastal corrosion recommends hot-dipped galvanized or stainless steel for exposed roof connectors and fasteners within 3,000 feet of the coastline, and discourages mechanically galvanized fasteners outdoors near the coast.
- Matching metals. The Metal Construction Association's fastener compatibility guide treats sites within 1,500 feet of salt water as a highly corrosive environment, says fasteners should match the panel material where possible, and does not recommend galvanized steel fasteners with aluminum panels. It also notes coastal use of carbon steel panels or fasteners may or may not void warranties, so ask the manufacturer.
- Panel metal and coating. MCA's metal roofing white paper says salt spray harms all common coatings on steel panels and that none tolerate trapped moisture for long. Its dissimilar metals bulletin warns that seawater chlorides are strong electrolytes and that aluminum should not contact copper. Aluminum panels are a common coastal choice; they are not part of our model's ranges, so price them from bids.
Underlayment and deck under a metal roof
FEMA's sloped-roof fact sheet recommends an upgraded underlayment as a secondary water barrier whenever the whole covering is replaced, rated to ASTM standards that match the area's wind ratings and securely fastened to the deck. Florida approvals list which underlayments go with each panel system, so the underlayment on your bid should match the approval. After tear-off, plywood repair is usually priced per sheet; get that rate in writing.
Insurance paperwork for a metal roof
The Department of Financial Services' mitigation discount guide says roof coverings such as metal panels that meet current Florida Building Code standards qualify for wind mitigation discounts on the windstorm portion of the policy. To claim it, keep the permit, final inspection, product approval or NOA number and invoice, and schedule a new wind mitigation inspection on the current OIR-B1-1802 form, which the DFS mitigation forms page says applies to inspections from April 1, 2026. Ask your insurer in writing what the change does to your premium. Roof-age rules and the inspector list are covered in our Florida roof guide.
How to compare Florida metal roof bids
Ask every roofer to itemize:
- Panel manufacturer, profile, metal (steel or aluminum), gauge and finish
- Florida product approval FL number or Miami-Dade NOA, and its design pressure
- Clip or screw type, material and spacing; ridge, eave and rake trim
- Underlayment product and how it is fastened
- Tear-off, disposal, deck repair rate per sheet, permit and inspections
- Panel finish warranty terms for your distance from salt water, plus workmanship coverage
A low bid often drops trim, flashing or the underlayment upgrade. Reconcile the scopes line by line before comparing totals, and see our estimate red flags and contractor hiring checklist.
Model your own roof size, pitch and shape with the roof replacement cost calculator, read how the numbers are built in our methodology, browse other roof cost guides, or compare roof costs in other states.
Sources: TheRoofBill 2026 cost model; BLS OEWS May 2025 (roofers); Homewyse standing-seam calculator; Florida Building Commission product approval reports; Miami-Dade product control NOAs; FEMA Technical Bulletin 8, P-2181 Fact Sheet 3.3.1 and Hurricane Michael best practices; Metal Construction Association technical documents; Florida DFS mitigation guide and forms page. Checked October 2026.
Frequently asked questions
How much does a metal roof cost in Florida in 2026?
TheRoofBill's 2026 model estimates $12,000–$23,600 for corrugated metal and $22,600–$36,300 for standing seam on a one-story Florida home with a 2,000 sq ft footprint, medium pitch, simple gable and one layer of tear-off. These are model outputs, not quotes. Homewyse's 2026 standing-seam calculator runs higher, so treat our figures as the lower end of planning.
Is standing seam or corrugated metal better for Florida?
Neither is automatically better. Standing seam uses concealed clips and costs more; corrugated and other exposed-fastener panels cost less but rely on screws and washers through the panel. What matters most is that the exact assembly carries a current Florida product approval (or Miami-Dade NOA in Miami-Dade and Broward) rated for the wind pressures at your address.
What metal and fasteners should I use near the Florida coast?
FEMA recommends hot-dipped galvanized or stainless steel for exposed roof connectors and fasteners within 3,000 feet of the coastline, and the Metal Construction Association advises against galvanized steel fasteners with aluminum panels. Ask the panel manufacturer in writing whether your distance from salt water affects the finish warranty.
Does a metal roof lower Florida insurance premiums?
It can help with wind mitigation credits, but do not assume a discount. The Florida DFS consumer guide says roof coverings such as metal panels that meet current Florida Building Code standards qualify for wind mitigation discounts, which apply only to the windstorm portion of the policy. Get a new wind mitigation inspection and ask your insurer to confirm the effect in writing.
Is a metal roof hurricane-proof?
No roof is hurricane-proof. FEMA's Hurricane Michael report found metal roofs on buildings built to the Florida Building Code generally performed better than other coverings, but it still documented metal roof damage. Performance depends on the tested assembly, deck, fasteners and installation.
Cost figures are planning estimates based on 2026 public data (Homewyse, Angi, Fixr, BLS). They are not contractor quotes. Full disclaimer · How we calculate.